Unipi Edge E410, E411, and E413 Controllers Built on Raspberry Pi CM4
Unipi has introduced the Edge E410, E411, and E413 controllers, a family of DIN-rail industrial devices based on the Raspberry Pi Compute Module 4. The systems combine PLC, RTU, IPC, and gateway functionality in a compact chassis targeting building automation, HVAC control, energy management, and industrial monitoring. All three models use the quad-core Arm Cortex-A72 […] ⌘ Read more

Waveshare Pairs RISC-V ESP32-P4 and ESP32-C6 for Wi-Fi 6, Bluetooth 5 LE, and PoE Support
Waveshare has released the ESP32-P4-WIFI6-POE-ETH, a compact development board built around the ESP32-P4 along with an ESP32-C6 wireless module. The design combines Wi-Fi 6, Bluetooth 5 LE, Ethernet, and optional PoE power delivery in a single platform aimed at multimedia processing, display and camera applications, and general embedded development. Like the earlier W … ⌘ Read more

Banana Pi Previews Its First SOPHGO BM1688-Based Compute Module
Banana Pi has previewed the BPI-SM9 16-ENC-A3, a compact deep learning compute module built around the SOPHGO BM1688 processor. The module is described as targeting low-power AI workloads, hardware video acceleration, and mixed-precision neural inference across microservers, edge systems, industrial platforms, and AIoT devices. The BM1688 datasheet does not appear to be available on the […] ⌘ Read more

OAK 4 D and OAK 4 S Standalone Edge Vision Cameras with PoE and 48MP Imaging
Luxonis has opened early access preorders for the OAK 4 D and OAK 4 S, two standalone edge-processing cameras designed for computer vision tasks. Both systems provide a 48MP RGB sensor with optional autofocus or wide-angle variants, USB 3 and PoE connectivity, IP67-rated enclosures, and on-device inference capabilities. Both devices are built around the RVC4 […] ⌘ Read more

Arduino Nesso N1 Debuts as a Compact RISC-V IoT Controller with Wi-Fi 6, Thread, and LoRa Connectivity
Arduino has released the Nesso N1, a compact IoT controller developed with M5Stack and built around the ESP32-C6. The device integrates a touch display, onboard sensors, and multiple wireless protocols inside a small enclosure aimed at rapid prototyping and portable embedded applications. The system is built around Espressif’s ESP32-C6 microc … ⌘ Read more

Engicam Showcases Computer Vision AI Kit Based on Renesas RZ/V2H Platform
Engicam has showcased the TIA RZ/V2H System-on-Module and its companion AI.DEV RZ/V2H development kit, both built around Renesas’ RZ/V2H processor. The module targets embedded applications in machine vision, autonomous robotics, and industrial automation, offering onboard AI acceleration and GPU capabilities optimized for real-time processing and advanced imaging. The TIA RZ/V2H module integrates … ⌘ Read more

SLogic16U3 USB3 Logic Analyzer Combines Compact Design with 3.2 Gbps Bandwidth
The SLogic16U3 is a next-generation USB3 logic analyzer designed for engineers and hobbyists seeking high-speed signal analysis in a small form factor. Measuring just 40 × 40 × 10 mm, it provides sampling rates of 800 M @ 4 channels, 400 M @ 8 channels, and 200 M @ 16 channels over a USB 3.0 […] ⌘ Read more

R1 Neo leverages GPS & compact rugged design for Meshtastic networks
The R1 Neo is a compact, water-resistant Meshtastic device for off-grid communication and navigation. Developed by Muzi, it features an aircraft-grade aluminum base with a carbon-fiber PETG shell, offering a 16% reduction in size compared to the previous R1. The enclosure includes O-ring and compression gaskets, an IP68-rated USB-C port, and a battery capable of […] ⌘ Read more

Solar-powered PV PI HAT delivers continuous off-grid operation for Raspberry Pi projects
Kickstarter recently featured the PV PI, a solar charging HAT designed to power Raspberry Pi and other 5V single board computers from a 12V LiFePO4 battery. The add-on enables continuous 24/7 off-grid operation through MPPT-based solar charging and intelligent power management. Developed by Melbourne-based engineer Luke Ditria and his team at AutoEcology, the PV PI [ … ⌘ Read more

Grinn GenioBoard Offers MediaTek Genio 700 SoM, Dual M.2 Expansion, and CRA-Ready Security
Grinn has unveiled the GenioBoard, a compact single-board computer aimed at accelerating development of embedded and AI-enabled systems. It integrates the company’s GenioSOM-510 and GenioSOM-700 modules built on MediaTek’s Genio processor family, combining multiple Arm Cortex-A cores with an integrated GPU and NPU for edge inference applications. Powered by the Medi … ⌘ Read more

iLabs Challenger+ RP2040 LoRa Mk II Adds Upgraded Power Architecture and BConnect Expansion
iLabs has released the Challenger+ RP2040 LoRa Mk II, an upgraded Feather-format microcontroller board that combines the Raspberry Pi RP2040 with an RFM95W LoRa radio module. The new revision refines the original design with improved noise isolation, enhanced power distribution, and added modular connectivity options. The board features a redesigned power supply … ⌘ Read more

Turris Omnia NG Introduced with OpenWRT-Derived OS, Wi-Fi 7, and 10 Gbps Networking
CZ.NIC has launched the Turris Omnia NG router, described as a new open-source device focused on security, performance, and modularity. It features a quad-core processor, Wi-Fi 7 connectivity, and M.2-based expandability, targeting users who require a long-lasting and adaptable networking platform. The Omnia NG is powered by a quad-core ARMv8 processor operating at 2.2 GHz […] ⌘ Read more

HUSKYLENS 2 Expands Edge AI Vision with MCP Integration and YOLO Model Support
DFRobot has introduced HUSKYLENS 2, a compact AI vision sensor for real-time visual recognition. It integrates a 6 TOPS dual-core processor, a 2 MP camera, and a touchscreen interface, offering over twenty pre-trained models for object, face, and hand recognition, along with support for custom YOLO-based models. The HUSKYLENS 2 is powered by a Kendryte […] ⌘ Read more

Radxa Launches AICore DX-M1 Edge AI Accelerator with DeepX DX-M1 NPU
After unveiling the AICore AX-M1 earlier this year, Radxa has launched the new AICore DX-M1, a compact M.2 M Key AI acceleration module designed for energy-efficient inference at the edge. The module is built around the DeepX DX-M1 processor, delivering up to 25 TOPS of INT8 performance within a 3 to 5 W power envelope. […] ⌘ Read more

AXC3000 Starter Kit Highlights Altera Agilex 3 FPGA with HyperRAM and MIPI Support
Arrow has introduced the AXC3000 Starter Kit, a compact FPGA development platform featuring the first production device from the Altera Agilex 3 family. Following the Agilex 5 AXE5000 devkit, this board provides a smaller form factor and focuses on low- to mid-range applications that demand efficient compute performance in compact designs. The Altera Agilex 3 […] ⌘ Read more

LILYGO T-Echo Plus Integrates LoRa, GNSS, and IMU in Rugged Wireless Smart Tag
LILYGO’s T-Echo Plus is a compact, battery-powered smart tag designed for wireless telemetry, motion tracking, and geolocation. It combines LoRa communication, GNSS positioning, Bluetooth Mesh, and a 6-axis IMU in an enclosure with both vibration and visual feedback, aiming to support mobile, field-deployed, or remote monitoring applications. The device uses the nRF52840 SoC from Nordic [ … ⌘ Read more

Easy RISC-V Provides an Interactive Way to Explore the RISC-V Architecture
Easy RISC-V is an open, browser-based learning resource that allows users to experiment with RISC-V assembly and gain a deeper understanding of how the architecture works. Created by developer Dramforever, the platform runs entirely online and does not require installation, offering a convenient way to study RISC-V instructions, registers, and execution flow from any device. […] ⌘ Read more

DietPi October 2025 Update Adds Support for NanoPi R3S, R76S, and Reworked Dashboard
The October 18th release of DietPi v9.18 introduces support for new FriendlyELEC single-board computers, a redesigned DietPi-Dashboard with improved security, and the addition of the LazyLibrarian eBook and audiobook manager. The update also includes bug fixes, filesystem improvements, and expanded compatibility for virtual devices   DietPi: DietPi is a lightweight, Debian-base … ⌘ Read more

Radxa Rolls Out Dragon Q6A Featuring Qualcomm QCS6490, 12 TOPS NPU, and 6th-Gen AI Engine
Radxa has rolled out the Dragon Q6A, a compact single-board computer built on Qualcomm’s QCS6490 octa-core platform. Designed for industrial, IoT, and edge computing environments, the board combines high-performance CPU and GPU cores with integrated AI acceleration, multiple display interfaces, and flexible storage options. Similar to the RUBIK Pi 3, the Dragon Q6A in … ⌘ Read more

M5Stack PowerHub IoT Development Kit Integrates ESP32-S3 and STM32 Coprocessor
M5Stack has introduced the PowerHub, a compact IoT controller designed for distributed power and device management. The ESP32-based PowerHub is described as providing a stable and flexible control platform that integrates communication interfaces, modular power input options, and precise monitoring capabilities. The PowerHub is built around the ESP32-S3-WROOM-1U-N16R8 module featuring a … ⌘ Read more

Silicon Labs SixG301 Series 3 SoCs Target Zigbee, Matter, and Thread Development
Silicon Labs has announced general availability of its new Series 3 platform, debuting with the SiMG301 and SiBG301 wireless SoCs. Built on a 22 nm process, the Series 3 family targets compute-intensive IoT applications that require higher security, integrated connectivity, and support for modern 2.4 GHz wireless protocols. Series 3 introduces a multi-core architecture that […] ⌘ Read more

ASUS Adds Amston Lake Atom x7000RE Based Models to Its Windows 11 IoT Lineup
ASUS has expanded its industrial motherboard lineup with new Amston Lake models built on Intel’s Atom x7000RE processors. Designed for Windows 11 IoT environments, these compact boards combine low power operation with support for high resolution video, extended temperature tolerance, and flexible connectivity for automation and embedded computing. All four processors are built on the […] ⌘ Read more

Astra SL2600 processors from Synaptics combine Arm cores and RISC-V Coral NPU
Synaptics has unveiled the Astra SL2600, a family of multimodal processors designed for edge computing across consumer, enterprise, and industrial IoT applications. The lineup debuts with the SL2610 product line, targeting low-power and high-performance designs used in smart home, automation, robotics, and retail systems. The Astra SL2600 family is built around the new Synaptics Torq […] ⌘ Read more

GIGABYTE AI TOP ATOM Introduces NVIDIA Grace Blackwell GB10 Performance for the Desktop
GIGABYTE has announced the AI TOP ATOM personal AI supercomputer designed for on-premises AI development. The compact system is powered by the NVIDIA Grace Blackwell GB10 Superchip and delivers supercomputer-level performance within a 1-liter chassis. The AI TOP ATOM integrates a 20-core Arm processor (10 Cortex-X925 and 10 Cortex-A725 cores) paired with 128 GB of […] ⌘ Read more

Orange Pi Previews Compact SBC with Eight-Core Allwinner A733 SoC
Orange Pi has unveiled the Orange Pi 4 Pro, a compact single-board computer designed for high-performance edge applications. It integrates an octa-core Allwinner A733 processor, a 3 TOPS NPU, and supports up to 16 GB of LPDDR5 memory, combining AI acceleration with a wide range of expansion interfaces. This SBC features the same SoC found […] ⌘ Read more

HackerBox 0119 Geopositioning Explores GPS and Mapping
HackerBox has released Issue 0119, titled “Geopositioning.” This edition marks ten years of the subscription series and focuses on satellite positioning and mapping through the ESP-WROOM-32 system-on-chip and the Thrifty Yeti Locator (TYL) platform. The kit combines hardware assembly with firmware development in the Arduino IDE to demonstrate GNSS and geolocation principles. According to the […] ⌘ Read more

Radxa Orion O6N Brings Cix P1 Performance to a Smaller Nano ITX Form Factor
Radxa has introduced the Orion O6N, a Nano ITX single board computer designed as a smaller and more power-efficient alternative to the earlier Orion O6. Both models share the same Cix P1 SoC and overall platform architecture, but the O6N adopts a more compact 120 x 120 mm form factor compared to the 170 x […] ⌘ Read more

Upbeat and SiFive Launch Ultra-Low Power RISC-V MCU with AI Acceleration
Upbeat Technology has announced the UP201 and UP301 family of RISC-V microcontrollers developed in collaboration with SiFive. The devices are intended for applications such as always-on IoT, wearables, drones, and sensor-based systems. The UP201 and UP301 integrate two SiFive Essential IP cores and two neural accelerators designed by Upbeat Technology. They implement Upbeat’s Error Detection […] ⌘ Read more

SigCore UC Industrial Control Module Prepares for Crowd Supply Launch
The OK153-S SBC from Forlinx Embedded is a compact industrial platform based on the Allwinner T153 processor. It supports Linux 5.10 and offers up to 1 GB of DDR3 RAM and 8 GB of eMMC storage. Key interfaces include triple Gigabit Ethernet, dual CAN-FD, and a Local Bus for PSRAM or FPGA expansion. The Allwinner […] ⌘ Read more

Compact M5Stack Unit C6L Integrates RISC-V ESP32-C6 and SX1262 for LoRa Meshtastic Use
The M5Stack Unit C6L is a compact LoRa module featuring the ESP32-C6 SoC and SX1262 transceiver. It supports 868 to 923 MHz operation for private LoRa networks with Meshtastic compatibility and options for custom development. The ESP32-C6 integrates a dual RISC-V architecture consisting of a high-performance 32-bit core running at 160 MHz and a low-power […] ⌘ Read more

Orange Pi Previews Orange Pi 6 Plus with 12-core architecture and dual 5G Ethernet ports
Orange Pi has introduced the Orange Pi 6 Plus, a single-board computer intended for high-performance and AI-oriented computing tasks. It uses the CIX CD8180/CD8160 SoC with a 12-core 64-bit CPU and an NPU rated at up to 45 TOPS. The SoC includes a 12-core architecture paired with an integrated graphics processor supporting hardware-accelerated ray tracing […] ⌘ Read more

DL40N Fanless 1.3L Mini PC with Intel Twin Lake Processors
The DL40N is a fanless 1.3-liter mini PC powered by Intel Twin Lake processors and up to 16GB DDR5 memory. It supports triple 4K display output, dual 2.5G Ethernet, and multiple USB and COM ports for reliable 24/7 operation in applications such as factory automation, digital signage, kiosks, and more. Built on Intel’s Twin Lake […] ⌘ Read more

Virtium Embedded Artists Expands SoM Lineup with Renesas RZ/G3E Platform
Virtium Embedded Artists has introduced the RZ/G3E SoM, a system-on-module based on the Renesas RZ/G3E processor for industrial and medical human-machine interface applications. The module incorporates a quad-core Arm Cortex-A55 processor running at 1.8 GHz, paired with a Cortex-M33 core at 200 MHz for real-time control. Graphics capabilities include support for dual Full HD displays […] ⌘ Read more

Arduino UNO Q Combines Qualcomm Dragonwing QRB2210 and STM32 MCU
Qualcomm Technologies has announced its plan to acquire Arduino, marking a major development in the embedded and maker ecosystems. The acquisition aims to combine Qualcomm’s edge computing and AI expertise with Arduino’s large developer community and open hardware approach. As part of the announcement, both companies introduced the Arduino UNO Q, a new dual-processor development […] ⌘ Read more

R1 Neo Meshtastic Device Introduced with GPS and nRF52840 Processor
The R1 Neo from Muzi Works is a compact, water-resistant Meshtastic device designed for long-range communication and GPS-based location tracking. Developed and assembled in Atlanta, it is the company’s first model built on a custom PCB featuring a dedicated I/O controller and integrated power management. The unit is powered by a Nordic nRF52840 microcontroller paired […] ⌘ Read more

Terasic Announces Starter Kit Featuring RISC-V Nios V Processor and Software Bundle
Terasic has introduced the Atum Nios V Starter Kit, a feature-rich evaluation platform designed to accelerate development with Altera’s Nios V processor. The kit is aimed at embedded engineers, system developers, and educators looking for a practical way to explore RISC-V–based designs on the Agilex 3 FPGA platform. According to Terasic’s announcement, the kit is […] ⌘ Read more

Radxa Announces Fogwise AIRbox Q900 for Industrial Edge AI
Radxa has announced the Fogwise AIRbox Q900, a rugged edge AI system powered by Qualcomm’s IQ-9075 processor. The compact unit delivers high-performance compute with industrial reliability, targeting real-time inference in manufacturing, robotics, smart cities, and research. The AIRbox Q900 is powered by the Qualcomm IQ-9075 SoC. It integrates an octa-core Kryo Gen 6 CPU based […] ⌘ Read more

GL.iNet Comet PoE Remote KVM with Power over Ethernet
GL.iNet has introduced the Comet PoE (GL-RM1PE), a compact remote KVM device for server management, industrial systems, NVR setups, and HomeLab use. It supports 4K@30 FPS remote display, two-way audio, PoE for simplified deployment, and includes onboard storage with self-hosted cloud support. The Comet PoE is equipped with a quad-core ARM Cortex-A53 processor, paired with […] ⌘ Read more

wafer.space Launches GF180MCU Run 1 for Custom Silicon Fabrication
wafer.space has launched its first pooled silicon fabrication run on Crowd Supply, known as GF180MCU Run 1. The campaign offers designers the opportunity to fabricate 1,000 chips of their own design using GlobalFoundries’ 180 nm mixed-signal process. The initiative is aimed at providing accessible, structured access to custom silicon, with dies expected to ship in […] ⌘ Read more

Forlinx OK3506-S12 Mini SBC Featuring Rockchip RK3506J and Pi-Compatible GPIO
Forlinx Embedded has introduced the OK3506-S12 Mini, a compact single board computer built around the Rockchip RK3506J processor. The board is intended for industrial applications that benefit from modest power consumption, stable operation, and long-term supply availability. The system-on-module integrates the RK3506J, which combines three Cortex-A7 cores running at up to 1.5GHz with a Co … ⌘ Read more

SigCore UC Industrial Control Module Prepares for Crowd Supply Launch
Crowd Supply recently featured the SigCore UC, an upcoming universal industrial I/O controller that combines rugged hardware with open-source software for engineers, researchers, and educators seeking a flexible control and data acquisition platform. Unlike typical development boards or expansion modules, SigCore UC arrives as a complete, ready-to-deploy solution. It is capable of handling real-world volt … ⌘ Read more

Tiny RISC-V Development Board with WCH CH32V317WCU6 Available from $6.80
The nanoCH32V317 is a compact development board created by MuseLab to simplify prototyping and embedded system development. It integrates USB connectivity, Ethernet support, and a straightforward programming interface through USB Type-C, providing an accessible platform for engineers and hobbyists working with RISC-V microcontrollers. The board is powered by the WCH CH32V317WCU6, a RISC-V microcontro … ⌘ Read more

DietPi September 2025 Update Brings Faster Backups and Roon Server Early Access
The September 20th release of DietPi v9.17 introduces smaller and more efficient system images, faster backups with reduced disk usage, and a new toggle for Roon Server’s early access builds. The update also addresses SPI bootloader flashing issues on Rockchip devices, improves Raspberry Pi sound card handling, and includes multiple bug fixes across tools and […] ⌘ Read more

MSI EdgeXpert Compact AI Supercomputer Based on NVIDIA DGX Spark
The MSI EdgeXpert is a compact AI supercomputer based on the NVIDIA DGX Spark platform and Grace Blackwell architecture. It combines a 20-core Arm CPU with NVIDIA’s Blackwell GPU to deliver high compute density in a 1.19-liter form factor, targeting developers, researchers, and enterprises running local AI workloads, prototyping, and inference. The EdgeXpert achieves up […] ⌘ Read more

ESP32 Bus Pirate Turns Low-Cost Boards into Multi-Protocol Debugging Tools
An open-source project called ESP32 Bus Pirate has been released, inspired by the classic Bus Pirate and adapted for modern ESP32-S3 hardware. Developed by Geo-tp, the firmware transforms low-cost ESP32 boards into versatile debugging devices that can probe, sniff, and interact with a wide range of digital and radio protocols. The firmware supports protocols such […] ⌘ Read more

Raspberry Pi Updates Keyboard PC with New 500+ Model
Raspberry Pi 500+ is the newest all-in-one personal computer in the Raspberry Pi family. It combines the Raspberry Pi 5 platform with a mechanical keyboard, upgraded memory, and integrated storage. The design builds on the earlier Raspberry Pi 400 and 500 models while adding higher specifications and new input features. The Raspberry Pi 500+ is […] ⌘ Read more

Radxa UFS/eMMC Module Reader and Storage Solution Enables Fast Flashing and Scalable Embedded Storage
Radxa’s UFS/eMMC Module Reader is a compact USB 3.0 adapter for flashing OS images, accessing firmware, and transferring large files. It supports both eMMC v5.0 and UFS 2.1 modules with speeds up to 5 Gbps The adapter is compatible with eMMC and UFS modules from Radxa, and also works with modules from platforms like PINE64 and […] ⌘ Read more

ROC-RK3506J-CC Board Integrates RK3506J and Dual LAN Support
The ROC-RK3506J-CC is a compact single-board computer based on Rockchip’s RK3506J processor. Designed for embedded systems with real-time demands, it supports a wide range of I/O and OS options and is available in both industrial and commercial variants. The RK3506J processor includes a tri-core ARM Cortex-A7 cluster alongside a single Cortex-M0 core, fabricated using a […] ⌘ Read more

CH32H417 Dual-Core RISC-V MCU Offers USB, Ethernet, and SerDes Support
WCH’s new CH32H417 microcontroller introduces a dual-core RISC-V architecture designed for embedded applications requiring high-speed connectivity and peripheral integration. It is built on the Qingke V5F core running at 400 MHz and the V3F core at 144 MHz. The microcontroller supports USB 3.2 Gen 1 with a 5Gbps PHY and dual-role host/device functionality, along with […] ⌘ Read more

EdgeLogix-1145 Brings Industrial Control and Edge Computing with Raspberry Pi CM5
The EdgeLogix-1145 is a rugged industrial controller that integrates edge computing, PLC functionality, and IIoT gateway capabilities. Designed around the Raspberry Pi CM5, it offers a compact, fanless platform designed for automation tasks in harsh environments such as factories, energy systems, and smart infrastructure. The system is built on the Broadcom BCM2712 SoC, a quad-core … ⌘ Read more